Tuesday, January 6, 2009

S O M 2 MARKS UNIT 2

UNIT-2 TWO MARKS (Mechanics of Materials)
1.list out the types of beams?
i) Cantilever beam
ii) Simply supported beam
iii) Overhanging beam
iv) Fixed beam
v) Continuous beam

2.Define Plane of bending?
The plane of the figure in which all of the loads, and all the deflections occur in that same plane is called as the plane of bending.

3.List out the types of support in beams?
i) Simple support
ii) Roller support
iii) Hinged support
iv) Fixed support

4. List out the types of loads acting on beams.
i) Point load
ii) Uniformly distributed load
iii) Varying load
iv) Impact load
v) Moving load



5. Define cantilever beam
A beam rigidly fixed at one end with the wall and hanging free at the other end is known as cantilever beam.

6. Define simply supported beam
if the ends of a beam are made to freely rest on supports, the beam is called as simply supported beam.

7. Define overhanging beam
A beam with its one end or both ends extended beyond the support or supports is known as overhanging beam.
8.Define continuous beam.
The beam, which is provided with more than two supports, is called as continuous beam.Eg.Bridge with more than one span.
9.Define fixed beam.
The beam whose both ends are rigidly fixed with the wall are called as fixed beam or built in beam .Eg .Beams in framed structures
10.Define concentrated or point load.
A load which is acting at a single point or concentrated on a very small length is called concentrated or point load.
11.Define uniformly distributed load.
A load which is distributed uniformly throughout the whole or a part of the length of the beam is called uniformly distributed beam .Eg. Weight of masonry wall over a beam.
12.Define varying load
A distributed load with varying intensity is called as varying load.
Eg. Load on lintel.
13.Define Shear force.
Shear force at any section of a loaded beam is defined as the resulting vertical force, acting to either right or left of the section.


14.Define Bending moment.
Bending moment at any section of a loaded beam is defined as the resulting upward or downward moment acting to either right or left of that section.
15.Define Hogging bending moment.
Hogging bending moment is defined as the bending moment at any section may bend the member at any section, so as to produce convexity above the center line.
16. Define Sagging bending moment.
Sagging bending moment is defined as the bending moment at any section may bend the member at any section, so as to produce concavity above the center line.
17. Define point of contra flexure
In an over hanging beam or continuous beam th point at which bending moment changes its sign between the supports of the beam.
18. What are the assumptions made in simple bending theory?
i. The beam is initially straight and every layer of it is free to expand or contract
ii. The material is homogenous and isotropic
iii. Youngs modulus is same in tension and compression
iv. Stresses are within elastic limit
v. The radius of curvature is large compared to depth of beam.
19. Define small deflection theory
the theory being derived with the assumption that radius of curvature is large compared to depth is valid only if deflections are less than 1/10th to 1/15th of beam .
20. Write the simple bending formula or bending equation
M/I = f/Y = E/R
21.Define Uniform strength beam
The beam in which the maximum bending stress at all cross sections is the same
22. What are the limitations of simple bending theory
i. the procedure holds good only for sections with at least one axis of symmetry
ii. The theory is applicable only to bending about principal axis

23. What is the formula for strain energy density of a thin walled tube?

Strain energy density = τ2/2g
24. Define shear flow
The product of shear stress (τ) and thickness t of the tube is same at every point of cross section. It is denoted by f.
25. Define modular ratio
The rotio of elastic module is known as modular ratio. It is denoted by m.
m = Es/Et where Es – elastic module for steel
Et - elastic module for t¬¬imber

No comments:

Post a Comment