Tuesday, October 20, 2009
Tuesday, January 6, 2009
S O M 2 MARKS UNIT 2
UNIT-2 TWO MARKS (Mechanics of Materials)
1.list out the types of beams?
i) Cantilever beam
ii) Simply supported beam
iii) Overhanging beam
iv) Fixed beam
v) Continuous beam
2.Define Plane of bending?
The plane of the figure in which all of the loads, and all the deflections occur in that same plane is called as the plane of bending.
3.List out the types of support in beams?
i) Simple support
ii) Roller support
iii) Hinged support
iv) Fixed support
4. List out the types of loads acting on beams.
i) Point load
ii) Uniformly distributed load
iii) Varying load
iv) Impact load
v) Moving load
5. Define cantilever beam
A beam rigidly fixed at one end with the wall and hanging free at the other end is known as cantilever beam.
6. Define simply supported beam
if the ends of a beam are made to freely rest on supports, the beam is called as simply supported beam.
7. Define overhanging beam
A beam with its one end or both ends extended beyond the support or supports is known as overhanging beam.
8.Define continuous beam.
The beam, which is provided with more than two supports, is called as continuous beam.Eg.Bridge with more than one span.
9.Define fixed beam.
The beam whose both ends are rigidly fixed with the wall are called as fixed beam or built in beam .Eg .Beams in framed structures
10.Define concentrated or point load.
A load which is acting at a single point or concentrated on a very small length is called concentrated or point load.
11.Define uniformly distributed load.
A load which is distributed uniformly throughout the whole or a part of the length of the beam is called uniformly distributed beam .Eg. Weight of masonry wall over a beam.
12.Define varying load
A distributed load with varying intensity is called as varying load.
Eg. Load on lintel.
13.Define Shear force.
Shear force at any section of a loaded beam is defined as the resulting vertical force, acting to either right or left of the section.
14.Define Bending moment.
Bending moment at any section of a loaded beam is defined as the resulting upward or downward moment acting to either right or left of that section.
15.Define Hogging bending moment.
Hogging bending moment is defined as the bending moment at any section may bend the member at any section, so as to produce convexity above the center line.
16. Define Sagging bending moment.
Sagging bending moment is defined as the bending moment at any section may bend the member at any section, so as to produce concavity above the center line.
17. Define point of contra flexure
In an over hanging beam or continuous beam th point at which bending moment changes its sign between the supports of the beam.
18. What are the assumptions made in simple bending theory?
i. The beam is initially straight and every layer of it is free to expand or contract
ii. The material is homogenous and isotropic
iii. Youngs modulus is same in tension and compression
iv. Stresses are within elastic limit
v. The radius of curvature is large compared to depth of beam.
19. Define small deflection theory
the theory being derived with the assumption that radius of curvature is large compared to depth is valid only if deflections are less than 1/10th to 1/15th of beam .
20. Write the simple bending formula or bending equation
M/I = f/Y = E/R
21.Define Uniform strength beam
The beam in which the maximum bending stress at all cross sections is the same
22. What are the limitations of simple bending theory
i. the procedure holds good only for sections with at least one axis of symmetry
ii. The theory is applicable only to bending about principal axis
23. What is the formula for strain energy density of a thin walled tube?
Strain energy density = τ2/2g
24. Define shear flow
The product of shear stress (τ) and thickness t of the tube is same at every point of cross section. It is denoted by f.
25. Define modular ratio
The rotio of elastic module is known as modular ratio. It is denoted by m.
m = Es/Et where Es – elastic module for steel
Et - elastic module for t¬¬imber
1.list out the types of beams?
i) Cantilever beam
ii) Simply supported beam
iii) Overhanging beam
iv) Fixed beam
v) Continuous beam
2.Define Plane of bending?
The plane of the figure in which all of the loads, and all the deflections occur in that same plane is called as the plane of bending.
3.List out the types of support in beams?
i) Simple support
ii) Roller support
iii) Hinged support
iv) Fixed support
4. List out the types of loads acting on beams.
i) Point load
ii) Uniformly distributed load
iii) Varying load
iv) Impact load
v) Moving load
5. Define cantilever beam
A beam rigidly fixed at one end with the wall and hanging free at the other end is known as cantilever beam.
6. Define simply supported beam
if the ends of a beam are made to freely rest on supports, the beam is called as simply supported beam.
7. Define overhanging beam
A beam with its one end or both ends extended beyond the support or supports is known as overhanging beam.
8.Define continuous beam.
The beam, which is provided with more than two supports, is called as continuous beam.Eg.Bridge with more than one span.
9.Define fixed beam.
The beam whose both ends are rigidly fixed with the wall are called as fixed beam or built in beam .Eg .Beams in framed structures
10.Define concentrated or point load.
A load which is acting at a single point or concentrated on a very small length is called concentrated or point load.
11.Define uniformly distributed load.
A load which is distributed uniformly throughout the whole or a part of the length of the beam is called uniformly distributed beam .Eg. Weight of masonry wall over a beam.
12.Define varying load
A distributed load with varying intensity is called as varying load.
Eg. Load on lintel.
13.Define Shear force.
Shear force at any section of a loaded beam is defined as the resulting vertical force, acting to either right or left of the section.
14.Define Bending moment.
Bending moment at any section of a loaded beam is defined as the resulting upward or downward moment acting to either right or left of that section.
15.Define Hogging bending moment.
Hogging bending moment is defined as the bending moment at any section may bend the member at any section, so as to produce convexity above the center line.
16. Define Sagging bending moment.
Sagging bending moment is defined as the bending moment at any section may bend the member at any section, so as to produce concavity above the center line.
17. Define point of contra flexure
In an over hanging beam or continuous beam th point at which bending moment changes its sign between the supports of the beam.
18. What are the assumptions made in simple bending theory?
i. The beam is initially straight and every layer of it is free to expand or contract
ii. The material is homogenous and isotropic
iii. Youngs modulus is same in tension and compression
iv. Stresses are within elastic limit
v. The radius of curvature is large compared to depth of beam.
19. Define small deflection theory
the theory being derived with the assumption that radius of curvature is large compared to depth is valid only if deflections are less than 1/10th to 1/15th of beam .
20. Write the simple bending formula or bending equation
M/I = f/Y = E/R
21.Define Uniform strength beam
The beam in which the maximum bending stress at all cross sections is the same
22. What are the limitations of simple bending theory
i. the procedure holds good only for sections with at least one axis of symmetry
ii. The theory is applicable only to bending about principal axis
23. What is the formula for strain energy density of a thin walled tube?
Strain energy density = τ2/2g
24. Define shear flow
The product of shear stress (τ) and thickness t of the tube is same at every point of cross section. It is denoted by f.
25. Define modular ratio
The rotio of elastic module is known as modular ratio. It is denoted by m.
m = Es/Et where Es – elastic module for steel
Et - elastic module for t¬¬imber
SOM 2 MARKS UNIT 1
UNIT 1 Two Marks (mechanics of materials)
1. Define Rigid body
A material or substance, which does not undergo any deformation when
subjected to external loading.
2. Define – Deformable solids
A material or solid undergoes deformation when subjected to external
loading.
3. Define Elastic material
A material, which undergoes a deformation when subjected to an external
loading such that it is capable of returning back to its original position, after
removing the external forces.
4. Define plastic material
A material, which undergoes a continuous deformation during the period
of loading and the deformation is permanent such that it does not regain its
original position on the removal of external loading.
5. Define stress
The force of resistance per unit area, offered by a body against
deformation.
Stress = σ = P / A External force or load
Cross sectional area.
6. Define deformation.
It is the change in dimensions i.e., increase or decrease in dimension due to the external force or loading.
Deformation δl = e X l
= strain x original length.
7. What are the units of stress and strain?
1. 1 Pascal (Pa) = 1 N/m2
2. Kilo pascal ( Kpa) = 103 N/m2
3. Mega pascal (Mpa) = 106N/m2
4. Giga Pascal (Gpa) = 109N/m2
5. N/mm2
6. Terapascal (Tpa) = 1012 N/m2
Strain has no unit.
8. Define strain.
The ration of change of dimension of the body to the original dimension.
It is the deformation per unit original dimension.
Strain, e = δl / l
Where, δl = Change in length L = Original length.
9. What are the types of axial stresses?
1) Tensile stress
2) Compressive stress.
3)
10. Define Tensile stress
When a body , section is subjected to two equal and opposite pulls and te body tends to increase its length, the stress induced is called the tensile stress.
Tensile stress = Tensile load (P)
Area (A)
11. Define tensile strain.
The strain corresponding to tensile strain, the result of which is the increase in length. Elongation per unit original length.
Tensile strain, e = (δl) Increase in length
(L) Original length
12. Define Elastic constants.
There is a limiting value of force upto and within which, the deformation entirely which, the disappears on the removal of force. The value of intensity of stress or stress corresponding to this limiting force is called elastic limit of the material.
13. Define compressive stress.
When a section is subjected to two equal and opposite pushes and the body tends to shorten or decrease its length, the stress induces is called compressive stress.
Compressive stress = σ = Compressive load (P)
Cross sectional area (A)
14. Define Compressive strain
The strain corresponding to compressive stress, the result of which is the decrease in length.
Contraction or shortening in length per unit original length.
Compressive strain, e = Decrease in length (δl)
Original length (l)
15. Define shear stress
When a section is subjected to two equal and opposite forces, acting tangentially across the resisting section, as a result of which the body tends to shear off across the section, the stress induced is called shear stress.
Shear stress = Shearing force
Resisting area
16. Define shear strain
The strain corresponding to shear stress
The ratio of transverse displacement or distortion to the original length is called shear strain.
Shear strain = Transverse Displacement
Original length
17. Define Hook’s Law.
When a material is loaded within its elastic limit, the stress is proportional to the strain.
Stress
= E =Constant
Strain
18. State the principle of shear stress.
It states that, A shear stress across a plane, is always accompanied by a balancing shear stress across the plane and normal to it.
19. Define Poisson’s ratio.
When a body is stress within its elastic limit, the lateral strain has a constant ratio to the linear strain.
Lateral strain
= Constant
Linear strain
This constant is known as Poisson’s ratio and is denoted by μ or 1/m.
20.Define Volumetric strain
The ratio of change in volume to the original volume is called as volumetric strain.
ev = δv / V
21. What is bulk modulus?
When a body is subjected to three mutually perpendicular stresses, of equal intensity the ratio of direct stress to the corresponding volumetric strain is known as bulk modulus.
Bulk modulus K = σ Direct stress
δv Volumetric strain
22. Give the relation between Bulk Modulus and Young’s modulus.
Bulk Modulus, K = mE
3 ( m-2)
Where, m = Modular rartio
E = Young’s Modulus
1/m = Poisson’s ratio
23. Define shear Modulus.
Modulus of Rigidity within the elastic limit, the shear stress is proportional to the shear strain.
Shear Modulus = τ Shear stress
Φ Shear strain
24. Give the relation between Modulus of Elasticity and Modulus of Rigidity.
C = mE
2(m+1)
Where 1/ m = Poisson’s ratio
E = Modulus of Elasticity.
25. Define Young’s Modulus
Within the elastic limit, the ratio of axial or linear stress to the corresponding linear strain is known as Young’s Modulus.
Young’s Modulus = E = Linear stress
Linear strain
1. Define Rigid body
A material or substance, which does not undergo any deformation when
subjected to external loading.
2. Define – Deformable solids
A material or solid undergoes deformation when subjected to external
loading.
3. Define Elastic material
A material, which undergoes a deformation when subjected to an external
loading such that it is capable of returning back to its original position, after
removing the external forces.
4. Define plastic material
A material, which undergoes a continuous deformation during the period
of loading and the deformation is permanent such that it does not regain its
original position on the removal of external loading.
5. Define stress
The force of resistance per unit area, offered by a body against
deformation.
Stress = σ = P / A External force or load
Cross sectional area.
6. Define deformation.
It is the change in dimensions i.e., increase or decrease in dimension due to the external force or loading.
Deformation δl = e X l
= strain x original length.
7. What are the units of stress and strain?
1. 1 Pascal (Pa) = 1 N/m2
2. Kilo pascal ( Kpa) = 103 N/m2
3. Mega pascal (Mpa) = 106N/m2
4. Giga Pascal (Gpa) = 109N/m2
5. N/mm2
6. Terapascal (Tpa) = 1012 N/m2
Strain has no unit.
8. Define strain.
The ration of change of dimension of the body to the original dimension.
It is the deformation per unit original dimension.
Strain, e = δl / l
Where, δl = Change in length L = Original length.
9. What are the types of axial stresses?
1) Tensile stress
2) Compressive stress.
3)
10. Define Tensile stress
When a body , section is subjected to two equal and opposite pulls and te body tends to increase its length, the stress induced is called the tensile stress.
Tensile stress = Tensile load (P)
Area (A)
11. Define tensile strain.
The strain corresponding to tensile strain, the result of which is the increase in length. Elongation per unit original length.
Tensile strain, e = (δl) Increase in length
(L) Original length
12. Define Elastic constants.
There is a limiting value of force upto and within which, the deformation entirely which, the disappears on the removal of force. The value of intensity of stress or stress corresponding to this limiting force is called elastic limit of the material.
13. Define compressive stress.
When a section is subjected to two equal and opposite pushes and the body tends to shorten or decrease its length, the stress induces is called compressive stress.
Compressive stress = σ = Compressive load (P)
Cross sectional area (A)
14. Define Compressive strain
The strain corresponding to compressive stress, the result of which is the decrease in length.
Contraction or shortening in length per unit original length.
Compressive strain, e = Decrease in length (δl)
Original length (l)
15. Define shear stress
When a section is subjected to two equal and opposite forces, acting tangentially across the resisting section, as a result of which the body tends to shear off across the section, the stress induced is called shear stress.
Shear stress = Shearing force
Resisting area
16. Define shear strain
The strain corresponding to shear stress
The ratio of transverse displacement or distortion to the original length is called shear strain.
Shear strain = Transverse Displacement
Original length
17. Define Hook’s Law.
When a material is loaded within its elastic limit, the stress is proportional to the strain.
Stress
= E =Constant
Strain
18. State the principle of shear stress.
It states that, A shear stress across a plane, is always accompanied by a balancing shear stress across the plane and normal to it.
19. Define Poisson’s ratio.
When a body is stress within its elastic limit, the lateral strain has a constant ratio to the linear strain.
Lateral strain
= Constant
Linear strain
This constant is known as Poisson’s ratio and is denoted by μ or 1/m.
20.Define Volumetric strain
The ratio of change in volume to the original volume is called as volumetric strain.
ev = δv / V
21. What is bulk modulus?
When a body is subjected to three mutually perpendicular stresses, of equal intensity the ratio of direct stress to the corresponding volumetric strain is known as bulk modulus.
Bulk modulus K = σ Direct stress
δv Volumetric strain
22. Give the relation between Bulk Modulus and Young’s modulus.
Bulk Modulus, K = mE
3 ( m-2)
Where, m = Modular rartio
E = Young’s Modulus
1/m = Poisson’s ratio
23. Define shear Modulus.
Modulus of Rigidity within the elastic limit, the shear stress is proportional to the shear strain.
Shear Modulus = τ Shear stress
Φ Shear strain
24. Give the relation between Modulus of Elasticity and Modulus of Rigidity.
C = mE
2(m+1)
Where 1/ m = Poisson’s ratio
E = Modulus of Elasticity.
25. Define Young’s Modulus
Within the elastic limit, the ratio of axial or linear stress to the corresponding linear strain is known as Young’s Modulus.
Young’s Modulus = E = Linear stress
Linear strain
Subscribe to:
Posts (Atom)